A device driver is nothing more than a named entity that supports the basic I/O functions - read, write, get config, and set config. Typically a device driver also uses and manages interrupts from the device as well. While the interface is generic and device driver independent, the actual driver implementation is completely up to the device driver designer.
That said, the reason for using a device driver is to provide access to a device from application code in as general purpose a fashion as reasonable. Most driver writers are also concerned with making this access as simple as possible while being as efficient as possible.
Most device drivers are concerned with the movement of information, for example data bytes along a serial interface, or packets in a network. In order to make the most efficient use of system resources, interrupts are used. This can allow for other application processing to take place while the data transfers are underway, with interrupts used to indicate when various events have occurred. For example, a serial port typically generates an interrupt after a character has been sent “down the wire” and the interface is ready for another. It makes sense to allow further application processing while the data is being sent since this can take quite a long time. The interrupt can be used to allow the driver to send a character as soon as the current one is complete, without any active participation by the application code.
The main building blocks for device drivers are found in the include file: cyg/io/devtab.h
All device drivers in eCos are described by a device table entry, using the “cyg_devtab_entry_t” type. The entry should be created using the DEVTAB_ENTRY macro, like this:
DEVTAB_ENTRY(l,name,dep_name,handlers,init,lookup,priv) Arguments: l - The "C" label for this device table entry. name - The "C" string name for the device. dep_name - For a layered device, the "C" string name of the device this device is built upon. handlers - A pointer to the I/O function "handlers" (see below). init - A function called when eCos is initialized. This function can query the device, setup hardware, etc. lookup - A function called when "cyg_io_lookup()" is called for this device. priv - A placeholder for any device specific data required by the driver. |
The interface to the driver is through the “handlers” field. This is a pointer to a set of functions which implement the various cyg_io_XXX() routines. This table is defined by the macro:
DEVIO_TABLE(l,write,read,get_config,set_config) Arguments: l - The "C" label for this table of handlers. write - The function called as a result of "cyg_io_write()". read - The function called as a result of "cyg_io_read()". get_config - The function called as a result of "cyg_io_get_config()". set_config - The function called as a result of "cyg_io_set_config()". |
When eCos is initialized (sometimes called “boot” time), the “init” function is called for all devices in the system. The “init” function is allowed to return an error in which case the device will be placed “off line” and all I/O requests to that device will be considered in error.
The “lookup” function is called whenever the cyg_io_lookup() function is called with this device name. The lookup function may cause the device to come “on line” which would then allow I/O operations to proceed. Future versions of the I/O system will allow for other states, including power saving modes, etc.
The standard serial driver supplied with eCos is structured as a hardware independent portion and a hardware dependent interface module. To add support for a new serial port, the user should be able to use the existing hardware independent portion and just add their own interface module which handles the details of the actual device. The user should have no need to change the hardware independent portion.
The interfaces used by the serial driver and serial implementation modules are contained in the file cyg/io/serial.h
Note: In the text below we use the notation <<xx>> to mean a module specific value, referred to as “xx” below.
The interface module contains the devtab entry (or entries if a single module supports more than one interface). This entry should have the form:
DEVTAB_ENTRY(<<module_name>>, <<device_name>>, 0, &serial_devio, <<module_init>>, <<module_lookup>>, &<<serial_channel>> ); Where: module_name - The "C" label for this devtab entry device_name - The "C" string for the device. E.g. "/dev/serial0". serial_devio - The table of I/O functions. This set is defined in the hardware independent serial driver and should be used. module_init - The module initialization function. module_lookup - The device lookup function. This function typically sets up the device for actual use, turning on interrupts, configuring the port, etc. serial_channel - This table (defined below) contains the interface between the interface module and the serial driver proper. |
Each serial device must have a “serial channel”. This is a set of data which describes all operations on the device. It also contains buffers, etc., if the device is to be buffered. The serial channel is created by the macro:
SERIAL_CHANNEL_USING_INTERRUPTS(l,funs,dev_priv,baud,stop,parity,word_length, flags,out_buf,out_buflen,in_buf,in_buflen) Arguments: l - The "C" label for this structure. funs - The set of interface functions (see below). dev_priv - A placeholder for any device specific data for this channel. baud - The initial baud rate value (cyg_serial_baud_t). stop - The initial stop bits value (cyg_serial_stop_bits_t) parity - The initial parity mode value (cyg_serial_parity_t) word_length - The initial word length value (cyg_serial_word_length_t) flags - The initial driver flags value out_buf - Pointer to the output buffer. NULL if none required. out_buflen - The length of the output buffer. in_buf - Pointer to the input buffer. NULL if none required. in_buflen - The length of the input buffer. |
If either buffer length is zero, no buffering will take place in that direction and only polled mode functions will be used.
The interface from the hardware independent driver into the hardware interface module is contained in the ‘funs’ table above. This is defined by the macro:
SERIAL_FUNS(l,putc,getc,set_config,start_xmit,stop_xmit) Arguments: l - The "C" label for this structure. putc - bool (*putc)(serial_channel *priv, unsigned char c) This function sends one character to the interface. It should return "true" if the character is actually consumed. It should return "false" if there is no space in the interface getc - unsigned char (*getc)(serial_channel *priv) This function fetches one character from the interface. It will be only called in a non-interrupt driven mode, thus it should wait for a character by polling the device until ready. set_config - bool (*set_config)(serial_channel *priv, cyg_serial_info_t *config) This function is used to configure the port. It should return "true" if the hardware is updated to match the desired configuration. It should return "false" if the port cannot support some parameter specified by the given configuration. E.g. selecting 1.5 stop bits and 8 data bits is invalid for most serial devices and should not be allowed. start_xmit - void (*start_xmit)(serial_channel *priv) In interrupt mode, turn on the transmitter and allow for transmit interrupts. stop_xmit - void (*stop_xmit)(serial_channel *priv) In interrupt mode, turn off the transmitter. |
The device interface module can execute functions in the hardware independent driver via “chan->callbacks”. These functions are available:
void (*serial_init)(serial_channel *chan);This function is used to initialize the serial channel. It is only required if the channel is being used in interrupt mode.
void (*xmt_char)(serial_channel *chan);This function would be called from an interrupt handler after a transmit interrupt indicating that additional characters may be sent. The upper driver will call the ‘putc’ function as appropriate to send more data to the device.
void (*rcv_char)(serial_channel *chan, unsigned char c);This function is used to tell the driver that a character has arrived at the interface. This function is typically called from the interrupt handler.