This is the mail archive of the
ecos-discuss@sources.redhat.com
mailing list for the eCos project.
Re: eCos tools binary installation under Cygwin
Ling Su wrote:
>
> Hi, Jifl,
>
> Do you ever meet following errors when you run pci1.exe test, following is
> what I met even I use the most updated cvs release, it is the same as
> before. The PCI bus scan failed for a SIGBUS bus error...Could you please
> take a look? Thanks!
I built pci1 from the latest sources (should be no different in any
relevant way to yours) and ran pci1. I got:
(gdb) c
Continuing.
Found device on bus 0, devfn 0x00:
Note that board is active. Probed sizes and CPU addresses invalid!
Device configuration failed - device already enabled
Vendor 0x1033 [NEC][NEC Corporation]
Device 0x001A [UNKNOWN]
Command 0x0146, Status 0x0280
Class/Rev 0x06800001 [Bridge Device][Other][]
Header 0x11FF0E
SubVendor 0x1111, Sub ID 0xFF19
BAR[0] 0x1C000000 / probed size 0x00000000 / CPU addr 0x1111FF15
BAR[1] 0x80000000 / probed size 0x00000000 / CPU addr 0x00000000
BAR[2] 0x00000000 / probed size 0x00000000 / CPU addr 0x1111FF16
BAR[3] 0x00000000 / probed size 0x00000000 / CPU addr 0x00000000
BAR[4] 0x00000000 / probed size 0x00000000 / CPU addr 0x1111FF17
BAR[5] 0x00000000 / probed size 0x00000000 / CPU addr 0x00000000
Wired to HAL vector 11
Found device on bus 0, devfn 0x18:
Device configuration succeeded
Vendor 0x1011 [DEC][Digital Equipment Corporation]
Device 0x0009 [DC21140][Fast Ethernet Ctrlr]
Command 0x0000, Status 0x0280
Class/Rev 0x02000022 [Network Controller][Ethernet][]
Header 0x11FF0E
SubVendor 0x1111, Sub ID 0xFF19
BAR[0] 0x00000001 / probed size 0xFFFFFF81 / CPU addr 0xAC000000
BAR[1] 0x00000000 / probed size 0xFFFFFF80 / CPU addr 0xC0000000
BAR[2] 0x00000000 / probed size 0x00000000 / CPU addr 0xFFFFFFFF
BAR[3] 0x00000000 / probed size 0x00000000 / CPU addr 0xFFFFFFFF
BAR[4] 0x00000000 / probed size 0x00000000 / CPU addr 0xFFFFFFFF
BAR[5] 0x00000000 / probed size 0x00000000 / CPU addr 0xFFFFFFFF
Wired to HAL vector 14
Strings in [] are from the PCI Code List at http://www.yourvote.com/pci
It seems that some of the device information has not been registered in
the PCI Code List. Please consider improving the database by registering
the [UNKNOWN] information for your devices. Thanks.
PASS:<pci1 test OK>
EXIT:<done>
I will send you the executable by private mail to see if it works on your
board.
Jifl
--
Red Hat, 35 Cambridge Place, Cambridge, UK. CB2 1NS Tel: +44 (1223) 728762
"Plan to be spontaneous tomorrow." || These opinions are all my own fault