This is the mail archive of the
ecos-discuss@sourceware.org
mailing list for the eCos project.
Re: Trouble with eCos Config Tool
- From: "Andy Jackson" <andy at grapevinetech dot co dot uk>
- To: "Ray Duran" <Ray dot Duran at FutureElectronics dot com>, "Tom Malcolmson" <Tom at Malcolmson dot com>
- Cc: <ecos-discuss at ecos dot sourceware dot org>
- Date: Fri, 29 Sep 2006 01:59:29 +0100
- Subject: Re: [ECOS] Trouble with eCos Config Tool
- References: <3CE39F664D1EE14293F6923CD00E42C704CD96C4@montremsg32.na.future.ca>
- Reply-to: "Andy Jackson" <andy at grapevinetech dot co dot uk>
Hi Ray/Tom,
Another option is to get the latest CVS sources and apply the patches on our
web site (www.xylanta.com), then compile with wxWidgets 2.6.3 rather than
the older 2.4.2 and see if that improves matters. I can send my build
scripts should you need them.
Alternatively there are binaries on the web site as well.
Andy..
----- Original Message -----
From: "Ray Duran" <Ray.Duran@FutureElectronics.com>
To: <ecos-discuss@ecos.sourceware.org>
Sent: Friday, September 29, 2006 12:30 AM
Subject: RE: [ECOS] Trouble with eCos Config Tool
Thanks for your reply Tom.
I was able to download the same file as you: "configtool-060710.exe"
from
http://www.ecoscentric.com/devzone/configtool.shtml
However, following the rest of the instructions on building wxwidget( in
order to ultimately rebuild eCos config) I am having a problem with.
I see some strange make errors. In fact they are the same errors found
by another:
http://sourceware.org/ml/ecos-discuss/2006-06/msg00061.html There was no
posted reply to this e-mail.
How where you able to rebuild the eCos config tool?
Thanks,
-Ray
-----Original Message-----
From: Tom Malcolmson [mailto:Tom@Malcolmson.com]
Sent: Thursday, September 28, 2006 2:53 PM
To: Ray Duran
Cc: ecos-discuss@ecos.sourceware.org
Subject: Re: [ECOS] Trouble with eCos Config Tool
Ray,
I too have recently started with eCos. I tried running configtool on
cygwin but it did not work. Like you, I looked into it and found that
this is apparently a problem with newer versions of cygwin.
In the end, I found the page that you referenced, and downloaded the
updated tool on this page. I think this is called
"configtool-060710.exe". This works for me.
http://www.ecoscentric.com/devzone/configtool.shtml
I take it that, though the above web page says that configtool is a
wxWidgets app, it is only partially so and still relies on unix calls
for which it needs cygwin.
Tom.
Ray Duran wrote:
Hello,
I am a new to the eCos community.
I followed the commands on the eCos webpage
wget --passive-ftp ftp://ecos.sourceware.org/pub/ecos/ecos-install.tcl
Then invoked installation tool
sh ecos-install.tcl
I followed the commands but did NOT select pre-built GNU toolchain as
I
had already
Downloaded a pre-built GNU ARM toolchain.
After selecting a mirror-site everything seemed fine and I got a
installation complete message.
So, I thought my next step was to launch the configtool by invoking
configtool.exe, but nothing happens.
I did a little research on the mailing list and saw some sort of
related
problems that say building the
Config tool is "tricky" and that there are known problems when running
against Cygwin 1.5.10 or later( which
applies to me). What am I missing? The procedure outline in the link
http://www.ecoscentric.com/devzone/configtool.shtml
seems to reference the CVS version. Is there a problem invoking the
Config tool with the non-CVS release?
Any help or tips greatly appreciated,
Regards,
-Ray
Ray Duran
Altera Design Specialist
Future Electronics
2220 O'Toole Avenue
San Jose Ca. 95131
408 232 1478
ray.duran@futureelectronics.com
The information in this transmission contains information that is
confidential and is intended only for the use of the individual or
entity to whom it is addressed. If the reader of this message is not
the
intended recipient please delete it and immediately notify the sender.
If the purpose of this transmission is to provide a quotation or to
confirm or acknowledge an order or to provide information in relation
to
the Products and Services offered, unless otherwise agreed in writing,
the FUTURE ELECTRONICS TERMS AND CONDITIONS OF SALE exclusively govern
the sale of Products and the provision of services by Future
Electronics
Inc. and its divisions, subsidiaries and affiliates and take
precedence
over supplemental or conflicting terms and conditions to which notice
of
objection is hereby given. The FUTURE ELECTRONICS TERMS AND CONDITIONS
OF SALE are available at www.futureelectronics.com and may be provided
on invoices, packing slips, order acknowledgements or other method.
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss